Witaj na Forum Linuxiarzy
Zanim zalogujesz się, by pisać na naszym forum, zapoznaj się z kilkoma zasadami savoir-vivre'u w dziale Administracja.
Wiadomości z problemami zamieszczone w wątku "Przywitaj się" oraz wszelkie reklamy na naszym forum będą usuwane.

Freeradius + Ubuntu 16.10 - nie działa, nie łączy

Zaczęty przez pd93, Listopad 11, 2016, 12:19:42 PM

Poprzedni wątek - Następny wątek

pd93

Witam.

Od tygodnia męczę się z konfiguracją Freeradiusa na wirtualnej maszynie z Ubuntu  :-[ Nie wiem zupełnie gdzie szukać problemu.

Router: TL-WR1043ND
Ubuntu: 16.10
IP routera: 192.168.1.1
IP laptopa z maszyną Ubuntu: 192.168.1.102 (czy wirtualna maszyna nie powinna mieć innego adresu IP?)
Próbuję się łączyć certyfikatem ca.der na Windows 10 + login i hasło ustalone w users.

Serwer jest wystartowany. Radtest nie działa dla 'radtest pawel password localhost 1812 testing123' tzn. kiedy wykomentuję localhosta w clients.conf. Kiedy localhost nie jest wykomentowany to działa.

Najpierw zrobiłem łączenie na sam login i hasło z poradnika: https://www.youtube.com/watch?v=WAaB2VUnZgUNie łączyło.

Dodałem certyfikaty z poradnikiem: http://billeter.blogspot.com/2011/03/wifi-radius.htmlNie łączy.

clients.conf

Spoiler (Rozwiń)

# -*- text -*-
##
## clients.conf -- client configuration directives
##
##   $Id$

#######################################################################
#
#  Define RADIUS clients (usually a NAS, Access Point, etc.).

#
#  Defines a RADIUS client.
#
#  '127.0.0.1' is another name for 'localhost'.  It is enabled by default,
#  to allow testing of the server after an initial installation.  If you
#  are not going to be permitting RADIUS queries from localhost, we suggest
#  that you delete, or comment out, this entry.
#
#

#
#  Each client has a "short name" that is used to distinguish it from
#  other clients.
#
#  In version 1.x, the string after the word "client" was the IP
#  address of the client.  In 2.0, the IP address is configured via
#  the "ipaddr" or "ipv6addr" fields.  For compatibility, the 1.x
#  format is still accepted.
#
#client localhost {
   #  Allowed values are:
   #   dotted quad (1.2.3.4)
   #       hostname    (radius.example.com)
   #ipaddr = 127.0.0.1

   #  OR, you can use an IPv6 address, but not both
   #  at the same time.
#   ipv6addr = ::   # any.  ::1 == localhost

   #
   #  A note on DNS:  We STRONGLY recommend using IP addresses
   #  rather than host names.  Using host names means that the
   #  server will do DNS lookups when it starts, making it
   #  dependent on DNS.  i.e. If anything goes wrong with DNS,
   #  the server won't start!
   #
   #  The server also looks up the IP address from DNS once, and
   #  only once, when it starts.  If the DNS record is later
   #  updated, the server WILL NOT see that update.
   #

   #  One client definition can be applied to an entire network.
   #  e.g. 127/8 should be defined with "ipaddr = 127.0.0.0" and
   #  "netmask = 8"
   #
   #  If not specified, the default netmask is 32 (i.e. /32)
   #
   #  We do NOT recommend using anything other than 32.  There
   #  are usually other, better ways to achieve the same goal.
   #  Using netmasks of other than 32 can cause security issues.
   #
   #  You can specify overlapping networks (127/8 and 127.0/16)
   #  In that case, the smallest possible network will be used
   #  as the "best match" for the client.
   #
   #  Clients can also be defined dynamically at run time, based
   #  on any criteria.  e.g. SQL lookups, keying off of NAS-Identifier,
   #  etc.
   #  See raddb/sites-available/dynamic-clients for details.
   #

#   netmask = 32

   #
   #  The shared secret use to "encrypt" and "sign" packets between
   #  the NAS and FreeRADIUS.  You MUST change this secret from the
   #  default, otherwise it's not a secret any more!
   #
   #  The secret can be any string, up to 8k characters in length.
   #
   #  Control codes can be entered vi octal encoding,
   #   e.g. "\101\102" == "AB"
   #  Quotation marks can be entered by escaping them,
   #   e.g. "foo\"bar"
   #
   #  A note on security:  The security of the RADIUS protocol
   #  depends COMPLETELY on this secret!  We recommend using a
   #  shared secret that is composed of:
   #
   #   upper case letters
   #   lower case letters
   #   numbers
   #
   #  And is at LEAST 8 characters long, preferably 16 characters in
   #  length.  The secret MUST be random, and should not be words,
   #  phrase, or anything else that is recognizable.
   #
   #  The default secret below is only for testing, and should
   #  not be used in any real environment.
   #
   #secret      = testing123

   #
   #  Old-style clients do not send a Message-Authenticator
   #  in an Access-Request.  RFC 5080 suggests that all clients
   #  SHOULD include it in an Access-Request.  The configuration
   #  item below allows the server to require it.  If a client
   #  is required to include a Message-Authenticator and it does
   #  not, then the packet will be silently discarded.
   #
   #  allowed values: yes, no
   #require_message_authenticator = no

   #
   #  The short name is used as an alias for the fully qualified
   #  domain name, or the IP address.
   #
   #  It is accepted for compatibility with 1.x, but it is no
   #  longer necessary in 2.0
   #
   #shortname   = localhost

   #
   # the following three fields are optional, but may be used by
   # checkrad.pl for simultaneous use checks
   #

   #
   # The nastype tells 'checkrad.pl' which NAS-specific method to
   #  use to query the NAS for simultaneous use.
   #
   #  Permitted NAS types are:
   #
   #   cisco
   #   computone
   #   livingston
   #   juniper
   #   max40xx
   #   multitech
   #   netserver
   #   pathras
   #   patton
   #   portslave
   #   tc
   #   usrhiper
   #   other      # for all other types

   #
   #nastype     = other   # localhost isn't usually a NAS...

   #
   #  The following two configurations are for future use.
   #  The 'naspasswd' file is currently used to store the NAS
   #  login name and password, which is used by checkrad.pl
   #  when querying the NAS for simultaneous use.
   #
#   login       = !root
#   password    = someadminpas

   #
   #  As of 2.0, clients can also be tied to a virtual server.
   #  This is done by setting the "virtual_server" configuration
   #  item, as in the example below.
   #
#   virtual_server = home1

   #
   #  A pointer to the "home_server_pool" OR a "home_server"
   #  section that contains the CoA configuration for this
   #  client.  For an example of a coa home server or pool,
   #  see raddb/sites-available/originate-coa
#   coa_server = coa
#}

# IPv6 Client
#client ::1 {
#   secret      = testing123
#   shortname   = localhost
#}
#
# All IPv6 Site-local clients
#client fe80::/16 {
#   secret      = testing123
#   shortname   = localhost
#}

#client some.host.org {
#   secret      = testing123
#   shortname   = localhost
#}

#
#  You can now specify one secret for a network of clients.
#  When a client request comes in, the BEST match is chosen.
#  i.e. The entry from the smallest possible network.
#
#client 192.168.0.0/24 {
#   secret      = testing123-1
#   shortname   = private-network-1
#}
#
#client 192.168.0.0/16 {
#   secret      = testing123-2
#   shortname   = private-network-2
#}


#client 10.10.10.10 {
#   # secret and password are mapped through the "secrets" file.
#   secret      = testing123
#   shortname   = liv1
#       # the following three fields are optional, but may be used by
#       # checkrad.pl for simultaneous usage checks
#   nastype     = livingston
#   login       = !root
#   password    = someadminpas
#}

#######################################################################
#
#  Per-socket client lists.  The configuration entries are exactly
#  the same as above, but they are nested inside of a section.
#
#  You can have as many per-socket client lists as you have "listen"
#  sections, or you can re-use a list among multiple "listen" sections.
#
#  Un-comment this section, and edit a "listen" section to add:
#  "clients = per_socket_clients".  That IP address/port combination
#  will then accept ONLY the clients listed in this section.
#
#clients per_socket_clients {
#   client 192.168.3.4 {
#      secret = testing123
#        }
#}

client 192.168.1.1{
   ipaddr = 192.168.1.1
   secret = password123
   require_message_authenticator = yes
}

Efekt freeradius -X

CytatFailed binding to authentication address * port 1812: Address already in use
/etc/freeradius/radiusd.conf[273]: Error binding to port for 0.0.0.0 port 1812

Dziękuję z góry za odpowiedzi  :) Nie wiem zupełnie co robię źle.

Albedo 0.64

Witaj. Problemu szukaj na linii host - guest. Jeśli używasz wirtualizacji to weź pod uwagę, że dużo zależy od systemu gospodarza i jego komunikacji z systemem gościem. Podzespoły komputera najpierw komunikują się z hostem a przez skonfigurowane porty dopiero z maszyną wirtualną. Maszyna wirtualna to tylko program działający w podstawowym systemie i nie ma co liczyć na 100% działanie systemu wirtualizowanego. Spróbuj zrobić to samo w ubuntu zainstalowanym na dysku i w tym wypadku proponuję bardziej stabilną i przewidywalną wersję 16.04 LTS.
MX Linux Xfce
Linux registered user 556565

pd93

Dziękuję za odpowiedź  ;)

W zasadzie potrzebuję Radiusa na chwilę (zadanie). Jedyna opcja na tę chwilę to instalacja Ubuntu na dysku zewnętrznym, ma to sens? Oczywiście konfigurację mogę zrobić jeszcze raz bo to trwa dość krótko.

Co masz dokładnie na myśli "Problemu szukaj na linii host - guest"? Co mogę jeszcze sprawdzić przed instalacją Ubuntu?

Albedo 0.64

Na myśli mam dokładnie to samo o czym już pisałem czyli konfiguracja portów w VM i współdzielenie ich między systemami gospodarza i gościa. Niestety, rzadko kiedy udaje się instalowanie sterowników w systemie gościu ale możesz się z tym zmierzyć.
MX Linux Xfce
Linux registered user 556565

pd93

Problem był banalny - należało przestawić w VirtualBoxie sieć z NAT na bridged. Dziękuję za nakierowanie na rozwiązanie ;)

Jako że już zadanie ukończone mogę polecić zainteresowanym najlepsze poradniki do FreeRadiusa:

Logowanie na login i hasło EAP-mschapv2:
https://www.youtube.com/watch?v=WAaB2VUnZgU

Logowanie na certyfikaty:
https://www.ossramblings.com/using-freeradius-ubuntu-server-wifi
plus
https://www.ossramblings.com/Freeradius-EAP-CRL-Generation

Zobacz najnowsze wiadomości na forum